SPRING SHACKLES/set (SH-435×562)

Calvert Racing Shackle and Bushing set

Fits: GM vehicles with factory MONO leafsprings.

Replace old worn out shackles and bushings with a fresh new set, including rubber bushings for the upper frame and rear spring eyes. 3-3/8″ center to center. Sold as a pair, required hardware included.

If you are unsure which part number will best fit your vehicle, please call Calvert Racing at 661-728-9600, Monday – Friday, 8:00am-4:30pm, PST.

$139.00

In Stock

SPRING SHACKLES/set (SH-435x562)
SPRING SHACKLES/set (SH-435x562) - Image 2

Additional information

Weight 6.25 lbs
Dimensions 11.5 × 8.5 × 5 in

GO TO CART

Categories: ,
SKU: SH-435x562

Recently Viewed:

No recently viewed products to display

Related products

    Accessories

    TIE DOWN BRACKETS/PAIR (TD-145)

    TIE DOWN BRACKETS – SET OF TWO, 45 degree angle

    One of the little annoyances many racers have is finding a place on their race car to tie it down onto a trailer or hauler without damaging the car and having to crawl under to find a spot for a strap/hook to load/unload/load again after a long day racing….

    IF YOU HAVE CALTRACS, YOU HAVE TIE DOWN POINTS!

    Secure your vehicle to a trailer or hauler with EASY TO INSTALL/EASY TO ACCESS Tie Down Brackets. Designed to bolt onto your CalTracs Mounts and LEAVE ON without affecting performance. Can be used in different configurations, depending on your needs.

    NOTE: Does not include straps. Fits STANDARD CALTRACS (all cars).

    1/4″ Zinc-Plated Steel, 45 degree angle. Overall size: 5-1/8″ x 4″; Hole is 1-3/8″ diameter. Manufactured in USA by Calvert Racing.

     

    (0 reviews)
    $30.00 Add to cart
    Accessories

    2.75 ” Axle Perch/pair (HDP-275)

    SPRING PERCHES FOR 2.75″ AXLE TUBE

    Set of (2) Two Perches. Fully enclosed for added strength, pedestal tabs ensure heat penetration when welded to housing. Perch extends to center line of axle tube for more surface area. Precision laser cut. Requires welding to axle, see graphic for info.

    Check out the comparison graphic to see how Calvert’s patented Heavy Duty Perches compare to other manufacturer’s stock perches.

    Patented HD Axle Perches. Universal design fits nearly every application. Available to fit the most common axle tube diameters; 2.25″, 2.5″, 2.75″, 3″, 3.25″ and 3.5″

    WELDING ONTO AXLE: Pinion angle recommendation is -2 to -4 degrees when used with CalTracs. NOTE: This is the angle of the pinion in relation to the angle of the output shaft of the transmission, NOT the driveshaft. Add the angle of the pinion yoke to the angle of the output shaft with the vehicle sitting at rest with weight on the tires.

    (0 reviews)
    $50.00 Add to cart
    Accessories

    U-Bolts, Square/set, 2.5″x11.5″ (SQ250x1150)

    SET OF FOUR SQUARE U-BOLTS w/hardware

    2.5″ axle diameter x 11.5″ long, axle BELOW springs.

    Square U-bolts, Grade 5 material, zinc plated, 9/16″ diameter. Set includes 4 U-bolts, plates, nuts and washers.

    We recommend torqueing truck/square u-bolts to 90-100 foot lbs. After running the vehicle down the track a few times, we also recommending checking the u-bolts and readjusting if necessary. Please see FEQ page or CalTracs Installation Guide for more info.

    (SQ300x900 shown)

    (0 reviews)
    $60.00 Add to cart
    Accessories

    FLIP CONVERSION KIT 1500 Series Trucks w/CalTracs INSTALLED (FLP-3134)

    FLIP CONVERSION KIT for 1500 SERIES TRUCKS (for CalTracs)
    1967-2019 Chevrolet Silverado and GMC Sierra Trucks

    Basic FLIP CONVERSION KIT for 1500 Series Trucks with CalTracs* and a 3″ axle tube and 2.5″ wide spring* already installed.
    Includes: Two Rear Mounts, Two patented Calvert Heavy Duty Perches, and set of Four U-Bolts with hardware.
    A flip kit moves the axle from beneath the leaf spring to on top of the leaf spring, which lowers the truck.

    ALSO AVAILABLE: Flip kit for 3″ axle tube and 2.5″ wide spring, part #FLP-3132
    *THIS CONVERSION KIT DOES NOT INCLUDE CALTRACS.

    (0 reviews)
    $209.00 Add to cart