HD SPRING CLAMPS/set of 2 (SCH-10)

HEAVY DUTY CLAMPS FOR 2.5″ SPRING, 1″ deep

Heavy duty steel, zinc coated spring clamps designed for Calvert Racing’s Split Mono Leafsprings. Includes two clamps, 2 bolts, 2 limiting tubes, and rivets. Rivets are designed to be pressed into spring hole to secure.

These clamps require a chamfered 3/8″ hole be drilled into the leaf for the rivet to be inserted and pressed to secure. NOTE: Back of spring , drill/chamfer the bottom spring. For the front of the spring, drill/chamfer the top spring.

Be sure to measure your springs to make sure the clamps will fit.

SCH-10 shown.

If you are unsure which part number will best fit your vehicle, please call Calvert Racing at 661-728-9600, Monday – Friday, 8:00am-4:30pm, PST.

$35.00

In Stock

SCH-10
HD SPRING CLAMPS/set of 2 (SCH-10) - Image 2
HD SPRING CLAMPS/set of 2 (SCH-10) - Image 3
HD SPRING CLAMPS/set of 2 (SCH-10) - Image 4
SCH-10

Additional information

Weight 2 lbs
Dimensions 11 × 6 × 1 in

GO TO CART

Categories: ,
SKU: SCH-10

Recently Viewed:

No recently viewed products to display

Related products

  • 2.75 " Axle Perch/pair (HDP-275)
    Accessories

    2.75 ” Axle Perch/pair (HDP-275)

    SPRING PERCHES FOR 2.75″ AXLE TUBE

    Set of (2) Two Perches. Fully enclosed for added strength, pedestal tabs ensure heat penetration when welded to housing. Perch extends to center line of axle tube for more surface area. Precision laser cut. Requires welding to axle, see graphic for info.

    Check out the comparison graphic to see how Calvert’s patented Heavy Duty Perches compare to other manufacturer’s stock perches.

    Patented HD Axle Perches. Universal design fits nearly every application. Available to fit the most common axle tube diameters; 2.25″, 2.5″, 2.75″, 3″, 3.25″ and 3.5″

    WELDING ONTO AXLE: Pinion angle recommendation is -2 to -4 degrees when used with CalTracs. NOTE: This is the angle of the pinion in relation to the angle of the output shaft of the transmission, NOT the driveshaft. Add the angle of the pinion yoke to the angle of the output shaft with the vehicle sitting at rest with weight on the tires.

    (0 reviews)
    $50.00 Add to cart
  • STRUT ROD KIT/pair (SR-40)
    Accessories

    STRUT ROD KIT/pair (SR-40)

    Built for Mopar A-Body.
    Sold as a pair.

    (SR-40 shown)

    (0 reviews)
    $250.00 Add to cart
  • U-Bolts, Square/set, 3"x13.5" (SQ300x1350)
    Accessories

    U-Bolts, Square/set, 3″x13.5″ (SQ300x1350)

    SET OF FOUR SQUARE U-BOLTS w/hardware

    3″ axle diameter x 13.5″ long, axle BELOW springs.

    Square U-bolts, Grade 5 material, zinc plated, 9/16″ diameter. Set includes 4 U-bolts, plates, nuts and washers.

    SQUARE U-BOLTS (spring OVER axle): We recommend torqueing truck/square u-bolts to 90-100 foot lbs. After running the vehicle down the track a few times, we also recommending checking the u-bolts and readjusting if necessary. Please see CalTracs Installation Guide for more info.

    (SQ300x900 shown)

    (0 reviews)
    $75.00 Add to cart
  • U-Bolts, Square/set, 3"x11" (SQ300x1100)
    Accessories

    U-Bolts, Square/set, 3″x11″ (SQ300x1100)

    SET OF FOUR SQUARE U-BOLTS w/hardware

    3″ axle diameter x 11″ long, axle BELOW springs.

    Square U-bolts, Grade 5 material, zinc plated, 5/16″ diameter. Set includes 4 U-bolts, plates, nuts and washers.

    Calvert Racing’s square u-bolts are 9/16″ ” diameter. We recommend torqueing truck/square u-bolts to 90-100 foot lbs. After running the vehicle down the track a few times, we also recommending checking the u-bolts and readjusting if necessary. Please see FEQ page or CalTracs Installation Guide for more info.

    (SQ300x900 shown)

    (0 reviews)
    $65.00 Add to cart