Accessories
Showing 19–27 of 102 results
-
Accessories
LOWERING BLOCKS/pair (LB-02)
CENTERING PIN 9/16″ (truck springs)
Set of two 1/2″ thick lowering blocks, interlocking and stackable via a 9/16″ centering pin and recess for most cars. You can stack more to achieve the drop you prefer: 1 pair= 1/2″ drop, 2 pairs= 1″ drop, etc.
Made with MILD STEEL, significantly stronger than aluminum.
LB-01 shown.
(0 reviews)$35.00 Add to cart -
Accessories
2 Degree PINION SHIMS/PAIR BLEMISHED (2-DB)
2 DEGREE SHIMS – SET OF TWO
BLEMISHED. These shims contain scratches and dings which do not affect the performance of the part. ONLY AVAILABLE THROUGH CALVERT RACING. Limited number available, subject to prior sale.
Pinion shims to help correct pinion angle under spring perches. Made of Billet aluminum. Includes washers.
(0 reviews)Original price was: $25.00.$15.00Current price is: $15.00. Read more -
Accessories
FLIP CONVERSION KIT 1500 Series Trucks w/CalTracs INSTALLED (FLP-3134)
FLIP CONVERSION KIT for 1500 SERIES TRUCKS (for CalTracs)
1967-2019 Chevrolet Silverado and GMC Sierra TrucksBasic FLIP CONVERSION KIT for 1500 Series Trucks with CalTracs* and a 3″ axle tube and 2.5″ wide spring* already installed.
Includes: Two Rear Mounts, Two patented Calvert Heavy Duty Perches, and set of Four U-Bolts with hardware.
A flip kit moves the axle from beneath the leaf spring to on top of the leaf spring, which lowers the truck.ALSO AVAILABLE: Flip kit for 3″ axle tube and 2.5″ wide spring, part #FLP-3132
*THIS CONVERSION KIT DOES NOT INCLUDE CALTRACS.(0 reviews)$209.00 Add to cart -
Accessories
SPRING SHACKLES/set (SH-325×562)
Calvert Racing Shackle and Bushing set for some GM cars that have Calvert Split Mono springs installed.
Fits: 1967-1981 Camaro/Firebird, 1968-1978 Nova/Ventura/Omega/Apollo with Calvert Split Mono springs installed.
Replace old worn out shackles with new shackles along with polyurethane bushings for the upper frame as well as the rear spring eye to reduce suspension binds and ensure a long service life. Includes required hardware. 9/16″ bolt.
(0 reviews)$129.00 Add to cart -
Accessories
ALUMINUM BUSHING/SET (BK-23)
1967-1981 Chevrolet Camaro
Kit includes two aluminum bushings and 2 steel inserts for FACTORY leafspring front spring eye, two alignment washers, one grease packet.
If you need replacement bushings for Calvert Springs, please call us directly.
(0 reviews)$65.00 Add to cart -
Accessories
U-Bolts, Round/set, 3.5″x7″ (UR350x70)
SET OF FOUR ROUND U-BOLTS w/hardware
3.5″ axle diameter x 7″ long, axle ABOVE springs
Round U-bolts, Grade 5 steel, rust resistant coating, 1/2″ diameter, Sets include 4 U-bolts, with nuts and washers.
(UR225x70 shown)
(0 reviews)$40.00 Add to cart -
Accessories
TIE DOWN BRACKETS/PAIR (TD-190M)
TIE DOWN BRACKETS – SET OF TWO (90 degree angle)
DESIGNED TO FIT STANDARD CALTRACS, CALTRACS FOR 1500 SERIES TRUCKS and CALTRACS FOR S-10 TRUCKS
Heavier than our other Tie Down Brackets: 1/4″ ” Zinc-Plated Steel, 90 degree angle. Overall size: 5-1/8″ x 4″; Hole is 1-3/8″ diameter. Manufactured in USA by Calvert Racing.
One of the little annoyances many racers have is finding a place on their race car to tie it down onto a trailer or hauler without damaging the car and having to crawl under to find a spot for a strap/hook to load/unload/load again after a long day racing….
IF YOU HAVE CALTRACS, YOU HAVE TIE DOWN POINTS!
Secure your vehicle to a trailer or hauler with EASY TO INSTALL/EASY TO ACCESS Tie Down Brackets. Designed to bolt onto your CalTracs Mounts and LEAVE ON without affecting performance. Can be used in different configurations, depending on your needs.
NOTE: Does not include straps.(0 reviews)$30.00 Add to cart -
Accessories
HANGERS/SET (H1500)
1988 – 1998 GM/Chevrolet 1500 series trucks (-2″ drop)
Designed to work directly with CalTracs. These hangers replace the original front hangar plates.
These front hangars are intended for use when aftermarket lowering hangars used to lower the truck will not allow the use of CalTracs on the spring. This product will lower the truck 2″ like most aftermarket hangars, but are designed to work directly with our CalTrac bar kits.
Includes (2) two hangers and required hardware.
NOTE: These will not fit long bed models or 454SS. without modification
(0 reviews)$175.00 Add to cart -
Accessories
U-Bolts, Square/set, 2.5″ x 9″ (SQ250x90)
SET OF FOUR SQUARE U-BOLTS w/hardware
2.5″ axle diameter x 9″ long, axle BELOW springs.
Square U-bolts, Grade 5 material, zinc plated, 5/16″ diameter. Set includes 4 U-bolts, plates, nuts and washers.
(SQ300x900 shown)
(0 reviews)$60.00 Add to cart