leafspring
Showing 1–9 of 44 resultsSorted by popularity
-
AccessoriesSPRING SLIDERS for Calvert Springs (SL-300CR )
SET OF TWO SPRING SLIDERS
Designed to fit Calvert Leafsprings installed on ALL CARS & TRUCKS (except Chevy Bel Air). Outside diameter aluminum bushings: 1″.
May also fit most Chrysler factory springs due to rear bearing size.
Heavy Duty roller bearings keep the leafspring and body from binding up during suspension movement. Replaces the existing shackles.
(0 reviews) -
Accessories
ALUMINUM BUSHING/SET (BK-37)
1982-2004 Chevrolet S-10
Kit includes two aluminum bushings* and 2 steel inserts, one grease packet for FACTORY leafspring front spring eye.
* NOTE: A second bushing set is included in case your vehicle requires a smaller outside diameter – some S-10s were manufactured with different sizes. The inserts will work with either size. Discard the unused bushing.
If you need replacement bushing for Calvert Springs, please call us directly.
(0 reviews) -
Accessories
ALUMINUM BUSHING/SET (BK-34)
1999-2018 Chevrolet/GM 1500 Series
Kit includes two aluminum bushings and 2 steel inserts, one grease packet for FACTORY leafspring front spring eye.
If you need replacement bushing for Calvert Springs, please call us directly.
(0 reviews) -
Accessories
SPRING SLIDERS for S10 Factory Multi Springs (SL-300S10)
SET OF TWO SPRING SLIDERS
Designed for S10 and S10/Blazer FACTORY Multi Leafsprings. Outside diameter aluminum bushings: 1-1/2″.
NOTE: If you have Calvert Springs, please use Part Number SL-300CR
Heavy Duty roller bearings keep the leafspring and body from binding up during suspension movement. Replaces the existing shackles.
SL-300CR shown.
(0 reviews) -
Accessories
SPRING SHACKLES/set (SH-325×562)
Calvert Racing Shackle and Bushing set for some GM cars that have Calvert Split Mono springs installed.
Fits: 1967-1981 Camaro/Firebird, 1968-1978 Nova/Ventura/Omega/Apollo with Calvert Split Mono springs installed.
Replace old worn out shackles with new shackles along with polyurethane bushings for the upper frame as well as the rear spring eye to reduce suspension binds and ensure a long service life. 3-1/4″ center to center. Includes required hardware. 9/16″ bolt.
(0 reviews) -
Accessories
ALUMINUM BUSHING/SET (BK-23)
1967-1981 Chevrolet Camaro
Kit includes two aluminum bushings and 2 steel inserts for FACTORY leafspring front spring eye, two alignment washers, one grease packet.
If you need replacement bushings for Calvert Springs, please call us directly.
(0 reviews) -
Accessories
HANGERS/SET (H1500)
1988 – 1998 GM/Chevrolet 1500 series trucks (-2″ drop)
Designed to work directly with CalTracs. These hangers replace the original front hangar plates.
These front hangars are intended for use when aftermarket lowering hangars used to lower the truck will not allow the use of CalTracs on the spring. This product will lower the truck 2″ like most aftermarket hangars, but are designed to work directly with our CalTrac bar kits.
Includes (2) two hangers and required hardware.
NOTE: These will not fit long bed models or 454SS. without modification
(0 reviews) -
Accessories
SPRING SHACKLES/set (SH-300x562A)
Calvert Racing Shackle and Bushing set for A-Body Mopar products.
Set includes two shackles and a total of eight polyurethane bushings (4 for the rear eye of the spring and 4 for the upper frame shackle). The shackles retain a 1/2″ shouldered bolt that necks down to a 3/8″ thread, 3-1/2″ center to center. Required nuts included.
(0 reviews) -
Accessories
SPRING SLIDERS for GM Factory Multi Springs (SL-300GM )
SET OF TWO SPRING SLIDERS
1967-1981 Chevrolet Camaro
1968-1978 Chevrolet Nova
Designed for certain GM FACTORY Multi Leafsprings. Outside diameter aluminum bushings: 1-5/8″.
NOTE: If you have Calvert Springs, please use Part Number SL-300CR
Heavy Duty roller bearings keep the leafspring and body from binding up during suspension movement. Replaces the existing shackles.
SL-300CR shown.
(0 reviews)
