Shop
Showing 127–135 of 722 resultsSorted by popularity
-
AccessoriesSPRING SLIDERS for 55-57 Chevy (SL-30055 )
SET OF TWO SPRING SLIDERS
1955-1957 Chevrolet Bel AirSliders replace spring shackles. Heavy Duty roller bearings keep the leafspring and body from binding up during suspension movement.
(0 reviews) -
Accessories
HANGERS/SET (H1510)
1999-2006 GM/Chevrolet 1500 series trucks (-2″ drop)
Designed to work directly with CalTracs. These hangers replace the original front hangar plates.
These front hangars are intended for use when aftermarket lowering hangars used to lower the truck will not allow the use of CalTracs on the spring. This product will lower the truck 2″ like most aftermarket hangars, but are designed to work directly with our CalTrac bar kits.
Includes (2) two hangers and required hardware.
NOTE: These will not fit long bed models or 454SS. without modification
(0 reviews) -
CalTracs - Trucks
CalTracs Truck (7600-300)
1962-1967 F-100 2WD with 3 inch diameter axle tube
Designed especially for trucks, axle BELOW springs. Bolt On traction system. Full pre-load adjustability, keeps axle from rotating/maintains pinion angle, eliminates spring wrap up, improves 60′ times. Black powder coated. Berlin-style pivot plates for most applications.
Specializing in leaf spring traction systems since 1995, the Calvert Racing Team knows what it takes to get your truck hooking harder than ever whether you’re drag racing, sled pulling or just towing. Helps eliminate wheel hop. Designed by racers for racers, CalTracs boasts unsurpassed quality and craftsmanship; the competition is eliminated right off the starting line. The preload link is made with Chromoly, lightweight but strong, ensuring maximum leverage and minimum flex. HD Rod Ends have a radial static load capacity of over 14,000 pounds. Two-piece aluminum front spring eye bushings assembly keeps the front pivot squared and rigid. The rear mounts are made with 5/16” mild steel to withstand the correct torque on your u-bolts, keeping the rear end from moving.
This kit requires and INCLUDES a set of square u-bolts.
SQUARE U-BOLTS (spring OVER axle): Calvert Racing’s square u-bolts are 9/16″ ” diameter. We recommend torqueing truck/square u-bolts to 90-100 foot lbs. After running the vehicle down the track a few times, we also recommending checking the u-bolts and readjusting if necessary. Please see FAQ page or CalTracs Installation Guide for more info.
FULL COLOR INSTALLATION GUIDE INCLUDED.
NOTE: Your final product may vary from photo depending on your application. Some applications require additional hardware. If your axle tube measures 3.25 inches diameter, please see part #7600-325
(0 reviews) -
CalTracs Links
CalTracs Force transfer Links/pair- 21.5″ (L190-215-250)
SET OF TWO
1.25″ diameter x 21.5″ force transfer links. Measure end to end. Measure end to end. Can be lengthened 3/4″ each end by turning once installed.
Made with 4130 Chromoly, the CalTracs preload link is light weight but strong, ensuring maximum leverage and minimum flex. Gloss black powder coated for added durability.
(0 reviews) -
CalTracs Rear Mounts
CalTracs Rear Spring Mount (MT-6)
SOLD SEPARATELY
Rear Spring Mount for CalTracs assembly. Designed for Ford Mustangs, double tab.
Made with 5/16″ mild steel to withstand the correct torque on your u-bolts and keep your rear-end from moving. Black gloss powder coated for extra durability.
MOUNT FITS BOTH LEFT AND RIGHT SIDE.
(0 reviews) -
Lifestyle
XXL Navy T-Shirt (T-2XN)
2X-LARGE NAVY T-SHIRT
50/50 Cotton/Poly blend for comfort and ease of wear. Silk screened front and back. Machine washable.
(T-LN shown)
(0 reviews) -
Leafsprings
Split Mono Leafsprings/pair -1″ Drop (220-34)
1962-1967 Chevrolet Chevy II*
1962-1967 Chevrolet Nova*
PRICE PER PAIR, SPLIT MONO LEAFSPRINGS
*If you have the original perches installed, you will need our Space Adapter Plates: SP-1 (for multi springs) or SP-3 (for mono springs). Please see Parts & Accessories page to order.
Tested on the fastest stock suspension cars in the world, Calvert’s Split Mono Leafsprings are designed to control and reduce excessive body separation in rear suspension and plants the rear tires without unloading.
All of Calvert Racing’s Split Mono Leafsprings are assembled to order with grade 8 hardware and heavy-duty alignment clamps. Aluminum bushings are pressed into the front spring eyes and polyurethane bushings in the rear spring eyes, these springs have been proven to withstand over 2,500 HP at ¼ mile ETs in the 6s.
NOTE: Calvert Racing Springs are designed for DRAG RACING and have a higher spring rate / stiffer ride than stock springs. Spring halves are dipped in black paint before assembly, but some raw steel may show due to deburring/grinding sharp edges.
Calvert Split Mono Leafsprings are designed to work with CalTracs to maintain arch. While street driving does not put undue stress on the springs, racing with Calvert springs without a traction device installed may result in bent or de-arched springs.
(0 reviews) -
CalTracs - Trucks
CalTracs Truck w/ Dana 70 (5450-70)
1994-2002 Dodge Ram 2500 4 WD, with Dana 70 Rear Housing
1994-2002 Dodge Ram 3500 4 WD, with Dana 70 Rear Housing
Designed especially for trucks, axle BELOW springs. Bolt On traction system. Full pre-load adjustability, keeps axle from rotating/maintains pinion angle, eliminates spring wrap up, improves 60′ times. Black powder coated. Berlin-style pivot plates for most applications.
Specializing in leaf spring traction systems since 1995, the Calvert Racing Team knows what it takes to get your truck hooking harder than ever whether you’re drag racing, sled pulling or just towing. Helps eliminate wheel hop. Designed by racers for racers, CalTracs boasts unsurpassed quality and craftsmanship; the competition is eliminated right off the starting line. The preload link is made with Chromoly, lightweight but strong, ensuring maximum leverage and minimum flex. HD Rod Ends have a radial static load capacity of over 14,000 pounds. Two-piece aluminum front spring eye bushings assembly keeps the front pivot squared and rigid. The rear mounts are made with 5/16” mild steel to withstand the correct torque on your u-bolts, keeping the rear end from moving.
FULL COLOR INSTALLATION GUIDE INCLUDED.
NOTE: Your final product may vary from photo depending on your application. Some applications require additional hardware.
(0 reviews) -
CalTracs - Trucks
CalTracs Truck (7410)
1999-2007 Ford F-250 4wd Diesel
1999-2007 Ford F-350 4wd Diesel
Designed especially for trucks, axle BELOW springs. Bolt On traction system. Full pre-load adjustability, keeps axle from rotating/maintains pinion angle, eliminates spring wrap up, improves 60′ times. Black powder coated. Berlin-style pivot plates for most applications.
Specializing in leaf spring traction systems since 1995, the Calvert Racing Team knows what it takes to get your truck hooking harder than ever whether you’re drag racing, sled pulling or just towing. Helps eliminate wheel hop. Designed by racers for racers, CalTracs boasts unsurpassed quality and craftsmanship; the competition is eliminated right off the starting line. The preload link is made with Chromoly, lightweight but strong, ensuring maximum leverage and minimum flex. HD Rod Ends have a radial static load capacity of over 14,000 pounds. Two-piece aluminum front spring eye bushings assembly keeps the front pivot squared and rigid. The rear mounts are made with 5/16” mild steel to withstand the correct torque on your u-bolts, keeping the rear end from moving.
FULL COLOR INSTALLATION GUIDE INCLUDED.
NOTE: Your final product may vary from photo depending on your application. Some applications require additional hardware.
THIS KIT REQUIRES AND INCLUDES SQUARE U-BOLTS.
SQUARE U-BOLTS (spring OVER axle): Calvert Racing’s square u-bolts are 9/16″ ” diameter. We recommend torqueing truck/square u-bolts to 90-100 foot lbs. After running the vehicle down the track a few times, we also recommending checking the u-bolts and readjusting if necessary. Please see FAQ page or CalTracs Installation Guide for more info.
(0 reviews)
