Shop
Showing 208–216 of 758 resultsSorted by popularity
-
CF Series 90/10 Race ShocksCF Series Front Racing Shocks/pair (CF35093-1)
1964-1973 Ford Mustang
Collapsed Length: 8.93″, Extended Length: 13.89″ *
* Approximate lengths. Please note that Racing Shocks require different collapsed/extended lengths than stock/street shocks.
Designed with dual compression valving, Calvert’s CF Series 90/10 Drag Shocks were engineered for cars with mid-range power for softest rate of rebound on the market to allow for better weight transfer and more weight over your rear tires.
Built-in high-speed valving keeps your front end from bottoming out on hard landings. Once you’re out of the hole, low speed compression is active, and a softer valving allows the front end to settle at the top end. Every application has been evaluated for best length, assuring that each vehicle has sufficient travel for maximum traction unlike other manufacturers who model their shocks after factory length shocks. No adjustments are required; designed to perform right out of the box. Lightweight, industrial design.
(0 reviews) -
Lifestyle
PIT MAT, 24″ x 70″, Roll Up (LS-pit mat)
NEW! Calvert Racing portable roll up PIT MAT
At approx. 24″ x 70″, this sturdy black PIT MAT is much larger than most portable pit mats and helps protect your back from the rockiest, hottest dirt or asphalt at the track, in your garage, driveway, or in your haulers. Convenient, sturdy, easy-to-use approx. 1/4″ thick EVA mat has two wide built-in elastic bands and a shoulder strap for easy transport. No foam to compress or wear down over time; just firm protection for your clothes and back.
Lower profile than creepers, perfect for lower vehicles. Easy roll up with attached elastic loops and a carrying strap, easy to store in your truck, toy hauler, trailer, etc. and grab when you need it. No storage bag to store or carry, just roll, loop and go!
Limited number in stock – order today!
(0 reviews) -
CF Series 90/10 Race Shocks
CF Series Front Racing Shocks/pair (CF22112)
UNIVERSAL FRONT RACING SHOCK
Eyelet on BOTH ENDS. Compressed 11 3/8″, Extended 17″ *
* Approximate lengths. Please note that Racing Shocks require different collapsed/extended lengths than stock/street shocks.
Designed with dual compression valving, Calvert’s CF Series 90/10 Drag Shocks were engineered for cars with mid-range power for softest rate of rebound on the market to allow for better weight transfer and more weight over your rear tires.
Built-in high-speed valving keeps your front end from bottoming out on hard landings. Once you’re out of the hole, low speed compression is active, and a softer valving allows the front end to settle at the top end. Every application has been evaluated for best length, assuring that each vehicle has sufficient travel for maximum traction unlike other manufacturers who model their shocks after factory length shocks. No adjustments are required; designed to perform right out of the box. Lightweight, industrial design.(0 reviews) -
CalTracs - Standard
CalTracs Standard Low Pro (6101)
THIS KIT INCLUDES LOW PROFILE (1 Hole) PIVOT PLATES.
Low Profile allows approx. 1.5″ more ground clearance for vehicles used for every day street driving.
1960-1963 Ford Falcon
Rod Ends/Heim Joints NOW COME WITH GREASE ZERKS. Add a small amount of grease to reduce chatter.
Designed by Race legend John Calvert. Bolt On traction system. Full pre-load adjustability, keeps axle from rotating/maintains pinion angle, improves 60′ times. Black powder coated for durability. Standard and Low Pro pivot plates available.
.
Specializing in leaf spring traction systems since 1995, the Calvert Racing Team knows what it takes to get your car hooking harder than ever. Designed by racers for racers, CalTracs boasts unsurpassed quality and craftsmanship; the competition is eliminated right off the starting line. The preload link is made with Chromoly, lightweight but strong, ensuring maximum leverage and minimum flex. ¾” Rod Ends have a radial static load capacity of over 14,000 pounds. Two-piece aluminum front spring eye bushings assembly keeps the front pivot squared and rigid. The rear mounts are made with 5/16” mild steel to withstand the correct torque on your u-bolts, keeping the rear end from moving.
.
NOTE: Part #2301 shown. Your final product may vary from photo depending on your application. Some applications require additional hardware. U-bolts NOT included in the kit but are available if desired.FULL COLOR INSTALLATION GUIDE INCLUDED.
(0 reviews) -
CalTracs - Standard
CalTracs Standard (6220)
THIS KIT INCLUDES 2-HOLE PIVOT PLATES.
Built for:
1963-1964 Ford Galaxie
NOTE: Hanger modification required. See graphic for basic instructions. Photos of actual install/modification, click HERE. Call 661-728-9600 during regular business hours if you have questions.
Rod Ends/Heim Joints NOW COME WITH GREASE ZERKS. Add a small amount of grease to reduce chatter.
NOTE: Your final product may vary from photo depending on your application. Some applications require additional hardware. U-bolts NOT included in the kit but are available if desired.
FULL COLOR INSTALLATION GUIDE INCLUDED.
(0 reviews) -
CalTracs - Standard
CalTracs Standard (4229)
THIS KIT INCLUDES 2-HOLE PIVOT PLATES.
Designed for applications with inboard springs.
1970-1974 Dodge Challenger w/ 3″ stock inboard kit
1966-1973 Dodge Charger w/ 3″ stock inboard kit
1975-1978 Dodge Charger w/ 3″ stock inboard kit
1966-1976 Dodge Coronet w/ 3″ stock inboard kit
1970-1973 Plymouth Barracuda w/ 3″ stock inboard kit
1966-1970 Plymouth Belvedere w/ 3″ stock inboard kit
1965-1970 Plymouth Fury w/ 3″ stock inboard kit
1975-1978 Plymouth Fury w/ 3″ stock inboard kit
1967-1971 Plymouth GTX w/ 3″ stock inboard kit
1968-1973 Plymouth Road Runner w/ 3″ stock inboard kit
1966-1974 Plymouth Satellite w/ 3″ stock inboard kit
Rod Ends/Heim Joints NOW COME WITH GREASE ZERKS. Add a small amount of grease to reduce rattle.
Designed by Race legend John Calvert. Bolt On traction system. Full pre-load adjustability, keeps axle from rotating/maintains pinion angle, improves 60′ times. Black powder coated for durability. Standard and Low Pro pivot plates available.
.
Specializing in leaf spring traction systems since 1995, the Calvert Racing Team knows what it takes to get your car hooking harder than ever. Designed by racers for racers, CalTracs boasts unsurpassed quality and craftsmanship; the competition is eliminated right off the starting line. The preload link is made with Chromoly, lightweight but strong, ensuring maximum leverage and minimum flex. ¾” Rod Ends have a radial static load capacity of over 14,000 pounds. Two-piece aluminum front spring eye bushings assembly keeps the front pivot squared and rigid. The rear mounts are made with 5/16” mild steel to withstand the correct torque on your u-bolts, keeping the rear end from moving.
.
NOTE: Your final product may vary from photo depending on your application. Some applications require additional hardware. U-bolts NOT included in the kit but are available if desired.FULL COLOR INSTALLATION GUIDE INCLUDED.
(0 reviews) -
Accessories
4 Degree/2″ PINION SHIMS/PAIR (4-D2)
4 DEGREE SHIMS – SET OF TWO
2″ wide. Fits 1.75′ – 2″ wide springs.
Pinion shims to help correct pinion angle under spring perches. Made of Billet aluminum.
NOW INCLUDES CENTER PIN LOCATOR BOLTS TO FIT ONTO CALVERT RACING SPLIT MONO LEAFSPRINGS. If you have a multi-springpack, you may need longer bolts.
Also available: 4 degree pinion shims
(0 reviews) -
Sale!Lifestyle
Five Carabiner Style Keyrings (LS-Key5)
Your whole crew needs these! FIVE Carabiner style keyrings with metal Calvert logo plate. Blue strap, metal plate, jump ring, and carabiner-style hook. 5.75″ long
(0 reviews) -
Leafsprings
Parabolic Mono Leafsprings -2″ Drop (PS210-09)
1955-1957 Chevrolet BelAir
-2″ DROP HEIGHT, 2″ WIDE MONO PARABOLIC LEAFSPRINGS
Alternative for aftermarket spring. Substantially lighter than multi-leafsprings.
Parabolic spring design distributes stress along the length of the spring, reducing stress on the arch. Each spring pair is arch verified. Center pins and bushings included.
CalTracs solid Bushings included when ordered directly from Calvert Racing.
NOTE: These springs are designed for DRAG RACING and have a higher spring rate / stiffer ride than stock springs. Springs are dipped in black paint before assembly, but some raw steel may show due to deburring/grinding sharp edges.
Calvert Mono Leafsprings are designed to work with CalTracs to maintain arch. While street driving does not put undue stress on the springs, racing with Calvert springs without a traction device installed may result in bent or de-arched springs.
(0 reviews)
