Shop
Showing 190–198 of 757 resultsSorted by popularity
-
CR Series 9 Way Adjustable SHocksCR Series Rear Shocks/pair (CR42150)
1955-1957 Chevrolet BelAir
NOTE: Please note on your order if you have a transbrake, footbrake, or manual transmission/stick shift.
Collapsed Length: 15.5″, Extended Length: 24″, Approx. Ride Height: 17.5″ *
* Approximate lengths. Please note that Racing Shocks require different collapsed/extended lengths than stock/street shocks.
Calvert Racing’s CR Series 9-Way Adjustable Rear Shocks twin tube design has what you need for all around best performance and maximum consistency. The dampeners allow you to control rear body separation through an external dial to keep the tires planted.
Constructed of steel with heavy duty 5/8 shaft ensures durability in the most stressful conditions, the 9-Way Adjustable dial is located outside the body for easy access to adjust rebound and to control rear body separation. Great for street/strip use.(0 reviews) -
CalTracs-MX
CalTracs MX (3700-MX)
Built for:
1982-2004 Chevrolet S10/Sonoma
1982-1994 Chevrolet Blazer
1982-2004 GMC Sonoma
1982-2004 GMC S-15
REAR END HOUSING: Original 7.5″, 8.8″, 9″, 10 Bolt, and 12 Bolt.
***
To get the most out of your CalTracs, we recommend that your installed CalTracs bars are close to parallel to the ground when fully loaded. Sometimes that configuration is difficult to achieve depending on the mods or equipment you have installed on your drag race car. CalTracs MX helps solve that!
***
Full CalTracs MX kits for cars feature our new MX 3-Hole Adjustable Rear Mounts, MX 4-Hole Adjustment Pivot Plates, and upgraded 9/16” bolt pivot hardware, these kits offer up to TWELVE adjustment settings (compared to two hole adjustable settings in Standard Drag Profile kits) to allow for fine tuning your CalTracs for the best HOOK possible on your racecar. Our new MX rear mount and MX pivot plate designs keep the overall CalTracs assembly set-up above the tire rim line on 15” wheels for track competition compliance and safety, just 1/2” longer than our Standard Drag Profile CalTracs.
EACH KIT ALSO INCLUDES a set of U-BOLTS for stock rear ends. If your vehicle has been modified, please call us so we can sent the correct size. 661-728-9600, M-F, 8am-4:30pm Pacific Time.
****
Designed by Race legend John Calvert. Bolt On traction system. Full pre-load adjustability, keeps axle from rotating/maintains pinion angle, improves 60′ times. Black powder coated for durability. Rod Ends/Heim Joints NOW COME WITH GREASE ZERK. Add a small amount of grease to minimize rattle.
Specializing in leaf spring traction systems since 1995, the Calvert Racing Team knows what it takes to get your car hooking harder than ever. Designed by racers for racers, CalTracs boasts unsurpassed quality and craftsmanship; the competition is eliminated right off the starting line. The preload link is made with Chromoly, lightweight but strong, ensuring maximum leverage and minimum flex. ¾” Rod Ends have a radial static load capacity of over 14,000 pounds. Two-piece aluminum front spring eye bushings assembly keeps the front pivot squared and rigid. The rear mounts are made with 5/16” mild steel to withstand the correct torque on your u-bolts, keeping the rear end from moving.
***Separate MX Mounts and Pivot Plates are available to upgrade your current CalTracs, call for details.
***
NOTE: MX Kits are not available for full sized trucks. Your final product may vary from photo depending on your application.
FULL COLOR INSTALLATION GUIDE INCLUDED.
(0 reviews) -
CR Series 9 Way Adjustable SHocks
HR Series High Resistance Rear Shocks/pair (HR42133)
HR Series High Resistance Shocks have all the benefits of our CR Series Rear Shocks PLUS the upper end of the dial offers higher resistance of separation on hard acceleration, perfect for Drag Racing. Dialing to the lower numbers ease the separation for more comfortable street driving.
1968-1974 AMC AMX, Javelin
1955-1957 Chevrolet BelAir (-1″ / -2″ drop)
1967-1969 Chevrolet Camaro
1962-1967 Chevrolet Nova Chevy II
1967-1979 Pontiac Firebird
1967-1979 Pontiac TransAm
NOTE: Please note on your order if you have a transbrake, footbrake, or manual transmission/stick shift.
Collapsed Length: 13.25″, Extended Length: 20″, Approx. Ride Height: 15.25″ *
* Approximate lengths. Please note that Racing Shocks require different collapsed/extended lengths than stock/street shocks.
Calvert Racing’s CR Series 9-Way Adjustable Rear Shocks twin tube design has what you need for all around best performance and maximum consistency. The dampeners allow you to control rear body separation through an external dial to keep the tires planted.
Constructed of steel with heavy duty 5/8 shaft ensures durability in the most stressful conditions, the 9-Way Adjustable dial is located outside the body for easy access to adjust rebound and to control rear body separation. Great for street/strip use.(0 reviews) -
Leafsprings
Split Mono Leafsprings/pair Stock Height (770-35)
1983-2011 Ford Ranger
STOCK HEIGHT SPLIT MONO LEAFSPRINGS, PER PAIR
Tested on the fastest stock suspension cars in the world, Calvert’s Split Mono Leafsprings are designed to control and reduce excessive body separation in rear suspension and plants the rear tires without unloading.
All of Calvert Racing’s Split Mono Leafsprings are assembled to order with grade 8 hardware and heavy-duty alignment clamps. Aluminum bushings are pressed into the front spring eyes and polyurethane bushings in the rear spring eyes, these springs have been proven to withstand over 2,500 HP at ¼ mile ETs in the 6s.
NOTE: Calvert Racing Springs are designed for DRAG RACING and have a higher spring rate / stiffer ride than stock springs. Spring halves are dipped in black paint before assembly, but some raw steel may show due to deburring/grinding sharp edges.
Calvert Split Mono Leafsprings are designed to work with CalTracs to maintain arch. While street driving does not put undue stress on the springs, racing with Calvert springs without a traction device installed may result in bent or de-arched springs.
(0 reviews) -
Leafsprings
Split Mono Leafsprings/pair Stock Height (660-34)
1970-1977 Ford Maverick
STOCK HEIGHT SPLIT MONO LEAFSPRINGS, PER PAIR
Tested on the fastest stock suspension cars in the world, Calvert’s Split Mono Leafsprings are designed to control and reduce excessive body separation in rear suspension and plants the rear tires without unloading.
All of Calvert Racing’s Split Mono Leafsprings are assembled to order with grade 8 hardware and heavy-duty alignment clamps. Aluminum bushings are pressed into the front spring eyes and polyurethane bushings in the rear spring eyes, these springs have been proven to withstand over 2,500 HP at ¼ mile ETs in the 6s.
NOTE: Calvert Racing Springs are designed for DRAG RACING and have a higher spring rate / stiffer ride than stock springs. Spring halves are dipped in black paint before assembly, but some raw steel may show due to deburring/grinding sharp edges.
Calvert Split Mono Leafsprings are designed to work with CalTracs to maintain arch. While street driving does not put undue stress on the springs, racing with Calvert springs without a traction device installed may result in bent or de-arched springs.
(0 reviews) -
Leafsprings
Split Mono Leafsprings/pair Stock Height (650-36)
1962-1965 Ford Fairlane
STOCK HEIGHT SPLIT MONO LEAFSPRINGS, PER PAIR
Tested on the fastest stock suspension cars in the world, Calvert’s Split Mono Leafsprings are designed to control and reduce excessive body separation in rear suspension and plants the rear tires without unloading.
All of Calvert Racing’s Split Mono Leafsprings are assembled to order with grade 8 hardware and heavy-duty alignment clamps. Aluminum bushings are pressed into the front spring eyes and polyurethane bushings in the rear spring eyes, these springs have been proven to withstand over 2,500 HP at ¼ mile ETs in the 6s.
NOTE: Calvert Racing Springs are designed for DRAG RACING and have a higher spring rate / stiffer ride than stock springs. Spring halves are dipped in black paint before assembly, but some raw steel may show due to deburring/grinding sharp edges.
Calvert Split Mono Leafsprings are designed to work with CalTracs to maintain arch. While street driving does not put undue stress on the springs, racing with Calvert springs without a traction device installed may result in bent or de-arched springs.
(0 reviews) -
CalTracs Rear Mounts
CalTracs Rear Spring Mount (MT-3)
SOLD SEPARATELY
LEFT Rear Spring Mount for CalTracs assembly. Designed for Chrysler vehicles.
Made with 5/16″ mild steel to withstand the correct torque on your u-bolts and keep your rear-end from moving. Black gloss powder coated for extra durability.
RIGHT Rear Spring Mount available, part # MT-4
(0 reviews) -
CalTracs - Standard
CalTracs Standard (6300)
THIS KIT INCLUDES 2-HOLE PIVOT PLATES.
Built for:
1960-1965 Mercury Comet / Cyclone
Designed by Race legend John Calvert. Bolt On traction system. Full pre-load adjustability, keeps axle from rotating/maintains pinion angle, improves 60′ times. Black powder coated for durability. Standard and Low Pro pivot plates available.
.
Specializing in leaf spring traction systems since 1995, the Calvert Racing Team knows what it takes to get your car hooking harder than ever. Designed by racers for racers, CalTracs boasts unsurpassed quality and craftsmanship; the competition is eliminated right off the starting line. The preload link is made with Chromoly, lightweight but strong, ensuring maximum leverage and minimum flex. ¾” Rod Ends have a radial static load capacity of over 14,000 pounds. Two-piece aluminum front spring eye bushings assembly keeps the front pivot squared and rigid. The rear mounts are made with 5/16” mild steel to withstand the correct torque on your u-bolts, keeping the rear end from moving.
.
NOTE: Your final product may vary from photo depending on your application. Some applications require additional hardware. U-bolts NOT included in the kit but are available if desired.FULL COLOR INSTALLATION GUIDE INCLUDED.
(0 reviews) -
CalTracs - Standard
CalTracs Standard (6900)
THIS KIT INCLUDES 2-HOLE PIVOT PLATES.
Built for:
1968-1976 Ford Torino / Grand Torino
Rod Ends/Heim Joints NOW COME WITH GREASE ZERKS. Add a small amount of grease to reduce chatter.
Designed by Race legend John Calvert. Bolt On traction system. Full pre-load adjustability, keeps axle from rotating/maintains pinion angle, improves 60′ times. Black powder coated for durability. Standard and Low Pro pivot plates available.
.
Specializing in leaf spring traction systems since 1995, the Calvert Racing Team knows what it takes to get your car hooking harder than ever. Designed by racers for racers, CalTracs boasts unsurpassed quality and craftsmanship; the competition is eliminated right off the starting line. The preload link is made with Chromoly, lightweight but strong, ensuring maximum leverage and minimum flex. ¾” Rod Ends have a radial static load capacity of over 14,000 pounds. Two-piece aluminum front spring eye bushings assembly keeps the front pivot squared and rigid. The rear mounts are made with 5/16” mild steel to withstand the correct torque on your u-bolts, keeping the rear end from moving.
.
NOTE: Your final product may vary from photo depending on your application. Some applications require additional hardware. U-bolts NOT included in the kit but are available if desired.FULL COLOR INSTALLATION GUIDE INCLUDED.
(0 reviews)
