Shop
Showing 199–207 of 607 resultsSorted by popularity
-
AccessoriesHANGERS/SET (H23)
1967-1969 Chevrolet Camaro
1967-1969 Pontiac Firebird
Designed to work directly with our CalTrac bar kits. These hangers replace the original front hangar plates.
Includes (2) two hangers and a hardware, leaf spring eye bolts and nuts, along with the bolts and clips that mount the hangar to the vehicle chassis.
(0 reviews) -
Accessories
MULTI SPRING CLAMPS/set of 6 (SCQ-01)
SPRING REBOUND STABILIZING CLAMPS FOR 2.5″ MULTI-SPRING/SET OF SIX
Rebound Stabilizing/Alignment fold over, quick on clamps 2.5″ wide multi-leafspring. See Graphic for recommended placement.
(0 reviews) -
Accessories
U-Bolts, Square/set, 3″x11″ (SQ300x1100)
SET OF FOUR SQUARE U-BOLTS w/hardware
3″ axle diameter x 11″ long, axle BELOW springs.
Square U-bolts, Grade 5 material, zinc plated, 5/16″ diameter. Set includes 4 U-bolts, plates, nuts and washers.
Calvert Racing’s square u-bolts are 9/16″ ” diameter. We recommend torqueing truck/square u-bolts to 90-100 foot lbs. After running the vehicle down the track a few times, we also recommending checking the u-bolts and readjusting if necessary. Please see FEQ page or CalTracs Installation Guide for more info.
(SQ300x900 shown)
(0 reviews) -
Leafsprings
Split Mono Leafsprings/pair (660-34)
1970-1977 Ford Maverick
STOCK HEIGHT SPLIT MONO LEAFSPRINGS, PER PAIR
Tested on the fastest stock suspension cars in the world, Calvert’s Split Mono Leafsprings are designed to control and reduce excessive body separation in rear suspension and plants the rear tires without unloading.
All of Calvert Racing’s Split Mono Leafsprings are assembled to order with grade 8 hardware and heavy-duty alignment clamps. Aluminum bushings are pressed into the front spring eyes and polyurethane bushings in the rear spring eyes, these springs have been proven to withstand over 2,500 HP at ¼ mile ETs in the 6s.
NOTE: Calvert Racing Springs are designed for DRAG RACING and have a higher spring rate / stiffer ride than stock springs. Spring halves are dipped in black paint before assembly, but some raw steel may show due to deburring/grinding sharp edges.
Calvert Split Mono Leafsprings are designed to work with CalTracs to maintain arch. While street driving does not put undue stress on the springs, racing with Calvert springs without a traction device installed may result in bent or de-arched springs.
(0 reviews) -
Leafsprings
Split Mono Leafsprings/pair (650-36)
1962-1965 Ford Fairlane
STOCK HEIGHT SPLIT MONO LEAFSPRINGS, PER PAIR
Tested on the fastest stock suspension cars in the world, Calvert’s Split Mono Leafsprings are designed to control and reduce excessive body separation in rear suspension and plants the rear tires without unloading.
All of Calvert Racing’s Split Mono Leafsprings are assembled to order with grade 8 hardware and heavy-duty alignment clamps. Aluminum bushings are pressed into the front spring eyes and polyurethane bushings in the rear spring eyes, these springs have been proven to withstand over 2,500 HP at ¼ mile ETs in the 6s.
NOTE: Calvert Racing Springs are designed for DRAG RACING and have a higher spring rate / stiffer ride than stock springs. Spring halves are dipped in black paint before assembly, but some raw steel may show due to deburring/grinding sharp edges.
Calvert Split Mono Leafsprings are designed to work with CalTracs to maintain arch. While street driving does not put undue stress on the springs, racing with Calvert springs without a traction device installed may result in bent or de-arched springs.
(0 reviews) -
Leafsprings
Split Mono Leafsprings/pair (220-35)
1962-1967 Chevrolet Chevy II*
1962-1967 Chevrolet Nova*
PRICE PER PAIR, SPLIT MONO LEAFSPRINGS
*If you have the original perches installed, you will need our Space Adapter Plates: SP-1 (for multi springs) or SP-3 (for mono springs). Please see Parts & Accessories page to order.
Tested on the fastest stock suspension cars in the world, Calvert’s Split Mono Leafsprings are designed to control and reduce excessive body separation in rear suspension and plants the rear tires without unloading.
All of Calvert Racing’s Split Mono Leafsprings are assembled to order with grade 8 hardware and heavy-duty alignment clamps. Aluminum bushings are pressed into the front spring eyes and polyurethane bushings in the rear spring eyes, these springs have been proven to withstand over 2,500 HP at ¼ mile ETs in the 6s.
NOTE: Calvert Racing Springs are designed for DRAG RACING and have a higher spring rate / stiffer ride than stock springs. Spring halves are dipped in black paint before assembly, but some raw steel may show due to deburring/grinding sharp edges.
Calvert Split Mono Leafsprings are designed to work with CalTracs to maintain arch. While street driving does not put undue stress on the springs, racing with Calvert springs without a traction device installed may result in bent or de-arched springs.
(0 reviews) -
CalTracs - Trucks
CalTracs Truck (7620-300)
1973-1979 Ford F-100 2WD with 3 inch diameter axle tube.
Designed especially for trucks, axle BELOW springs. Bolt On traction system. Full pre-load adjustability, keeps axle from rotating/maintains pinion angle, eliminates spring wrap up, improves 60′ times. Black powder coated. Berlin-style pivot plates for most applications.
Specializing in leaf spring traction systems since 1995, the Calvert Racing Team knows what it takes to get your truck hooking harder than ever whether you’re drag racing, sled pulling or just towing. Helps eliminate wheel hop. Designed by racers for racers, CalTracs boasts unsurpassed quality and craftsmanship; the competition is eliminated right off the starting line. The preload link is made with Chromoly, lightweight but strong, ensuring maximum leverage and minimum flex. HD Rod Ends have a radial static load capacity of over 14,000 pounds. Two-piece aluminum front spring eye bushings assembly keeps the front pivot squared and rigid. The rear mounts are made with 5/16” mild steel to withstand the correct torque on your u-bolts, keeping the rear end from moving.
This kit requires and INCLUDES a set of square u-bolts.
FULL COLOR INSTALLATION GUIDE INCLUDED.
NOTE: Your final product may vary from photo depending on your application. Some applications require additional hardware. If your axle tube measures 3.25 inches diameter, please see part #7620-325
(0 reviews) -
CR Series 9 Way Adjustable SHocks
CR Series Rear Shocks/pair (CR24130)
1960-1964 Ford Galaxie
1970-1975 Ford Maverick (+1″ height)
NOTE: Please note on your order if you have a transbrake, footbrake, or manual transmission/stick shift.
Collapsed Length: 13.5″, Extended Length: 21″, Approx. Ride Height: 15.5″ *
* Approximate lengths. Please note that Racing Shocks require different collapsed/extended lengths than stock/street shocks.
Calvert Racing’s CR Series 9-Way Adjustable Rear Shocks twin tube design has what you need for all around best performance and maximum consistency. The dampeners allow you to control rear body separation through an external dial to keep the tires planted.
Constructed of steel with heavy duty 5/8 shaft ensures durability in the most stressful conditions, the 9-Way Adjustable dial is located outside the body for easy access to adjust rebound and to control rear body separation. Great for street/strip use.(0 reviews) -
CalTracs Rear Mounts
CalTracs Rear Spring Mount (MT-4)
SOLD SEPARATELY
RIGHT Rear Spring Mount for CalTracs assembly. Designed for Chrysler vehicles.
Made with 5/16″ mild steel to withstand the correct torque on your u-bolts and keep your rear-end from moving. Black gloss powder coated for extra durability.
LEFT Rear Spring Mount available, part # MT-3
(0 reviews)
